D-sub adapters that allow mating cables to lie flat in floor boxes, or pre-wired install cables to be used with “back-to-back” panel connectors when clearance is limited. Available in D-sub 9 pin and…
Terminating installed video cables directly to the standard high density D-sub 15-pin connector (“HDD15”) has long been problematic, even with 3mm diameter cable, and virtually impossible with 6mm+…
D-sub connectors with screw terminal connection for cable or panel mounting. Available in 9-pin D-sub and 15-pin high density D-sub versions. The Phoenix connection blocks provide screw terminals…
The Ikon DVI-ST screw terminal adapter brings all the DVI contacts out to screw terminals with minimal signal loss, and is designed for panel mounting applications. Tapped M3, threaded mounting posts…
This fully populated DVI female to DVI female adapter is panel mountable to allow coupling of two DVI cables through a panel or bulkhead. It is fully compatible with DVI-I single/dual link, DVI-D…
This is a special HDMI female-female adapter that mounts into apertures punched for D-sub 9 pin connectors, enabling HDMI terminations in commonly available mounting plates and panels.
The Ikon HDMI adapters offer a range of methods of interfacing and terminating HDMI format signals. The HDMI-BB is a back-to-back adapter for use where the rear cable approaches directly from the…
A useful HDMI female-female coupler, intended for situations where HDMI cable routings cannot avoid tight bends. As with most high data-rate cables, HDMI cables suffer degraded performance if their…
This uses power from the HDMI bus to repeat the signal, therefore no external power supply is required. It allows cable runs to be extended up to 30 metres, according to cables used. It also can…
This unit enables cables to be joined together and carry signals over longer distances than the maximum length of individual cables permit. Maximum cable lengths (1080p) are 50 metres on the source…
This simple 2-input, 1-output device permits switching between two HDMI sources. It has two HDMI female connectors in a housing with a push-button switch, and an attached 500mm cable with an HDMI…
Gefen manufacture a very extensive range of video and data interfacing units, including a series of HDMI splitters, distribution amplifiers, cable extenders and matrices, plus useful tools like a…
The Ikon HDD15 floor/wallbox and panel adapters enable provision of HDD15 female outlets where rear clearance is limited. The DADO-90P is an adapter with an HDD15 female connector mounted at right…
For glare-free viewing of monitors in the field, Hoodman offer monitor hoods from four to twenty-one inches, including viewfinder type (HVF). For high-definition TV use, HD-series tapered hoods with…
These pre-wired cables are for use with most camera microphone inputs. They have a black XLR 3-pin female for the microphone connection and a 3.5mm 3-pole jack plug, straight or right-angle, for the…
Hoodman Corporation design and manufacture digital camera and camcorder accessories, with products sold world-wide. Glare-fighting hoods are the primary focus of Hoodman's product line. Hoodman's…
The TL-480HD series of monitors are designed specifically for use as on-camera monitors in applications in film and TV production and HD video shooting with DSLR cameras. There are four models…
The Ki Pro Mini is a 10-bit, 4:2:2, miniature field recorder for creating 'ready- to-edit' professional digital video. It supports an Apple file-based workflow by recording standard Apple ProRes 422…
As any spectacle-wearing photographer knows, ordinary glasses can be very frustrating with the need to remove them to see properly through the camera viewfinder, thus preventing the other eye being…
These are specifically designed to fit the Red 5.6 and 7 inch onboard LCD monitors. They have rugged nylon exteriors with rigid inserts. Elastic straps are sewn into each hood to mount it on the LCD…
The HoodLoupe 3.0 is designed for use with the screens of digital cameras, to exclude excess light and ease adjustment of composition, focus and exposure, either when shooting stills or video. A…
The Orbitor is a shoulder-mounted camera support system that provides a balanced and stable platform when shooting with a camcorder or DLSR, reducing fatigue on long shoots. Accessories such as…
This system is designed to offer a smooth and stable shooting base for professional camcorders and DSLR cameras, allowing 14.4V V-Mount batteries to supply the power and provide considerably longer…
These cables have a in-line up or down-converting voltage-regulator to power a 7.2 volt camera and a 12 volt camera light simultaneously from a 12-14.8 volt battery, or both a 7.2 volt camera and a 6…
The WristShot is a cuff which fits around the lower forearm and wrist, with an articulated arm to mount a camcorder. The result transfers the weight of the camcorder to the forearm, eliminating wrist…
Hoodman Hoods Hoodman digital camera hoods and camcorder hoods are made of sturdy plastic inserts, wrapped in water-resistant nylon. They are attached by simple elastic straps and are designed to…
These accessories are designed to enhance the operation of digital single-lens-reflex (SLR) professional stills cameras, with provision of scratch-resistant caps, hoods, a screen loupe and magnifiers…
These hoods are designed as sun-shades for computer screens. They are designed to eliminate glare, improve contrast and allow private viewing. An alternative use for the hoods is in sensitive…
The Hoodman RAW SxSxSDHC is an alternative memory adapter for Sony SxS applications, and is designed for use with Hoodman RAW SDHC memory cards but is also compatible with SDXC and UHS-1 cards. A key…
The E-Films MxR and e-LCR memory card adapters allow SDHC memory cards to be used with Sony EX1 and EX3 camcorders. The MxR and e-LCR were engineered from the ground up to allow SDHC cards to be used…
The e-MCR multi express card reader to USB offers 4x transfer speed of E-films MxR, e-LCR and Hoodman Raw SxS card replacements (Sony original SxS cards are not supported). Simply load the e-MCR with…
Transcend are a premium manufacturer of a range of flash memory storage devices, offering SDHC memory cards in a range of sizes and class ratings. SDHC Class 6 cards Transcend's SDHC card is based…
The Integral UltimaPro CF carda are intended for professional and amateur photographers, to capture high-resolution images and video in a DSLR or high-end compact cameras. They use a 'state of the…
Intended to 'fulfil the demanding requirements of performance-conscious photographers', offering high speed read and write performance for users of DSLR cameras, these are offered in 400X and 600X…
This inventive product makes it possible to view the live display and control DSLR cameras from a distance of up to 100 metres over a 2.4GHz link. The 3.5 inch LCD screen is particularly useful when…
Please select from the list of categories above
